Magnetic Properties of Thin Epitaxial SiC Layers Grown by the Atom-Substitution Method on Single-Crystal Silicon Surfaces

Semiconductors - A cycle of experimental investigations is carried out, specifically, the measurements and analysis of field dependences of the static magnetic susceptibility in samples of...     

Signs of Degradation of Carbide Phases in Chromium-Nickel Cast Iron at the Operating Temperatures of Forming Rolls

Materials Science - We study the causes and signs of degradation of cementite in chromium-nickel cast iron used for the production of massive forming rolls and the specific features of structural...     

Organofluorine Hydrazone Derivatives as Multifunctional Anti-Alzheimer's Agents with CK2 Inhibitory and Antioxidant Features

A set of novel hydrazone derivatives were synthesized and analyzed for their biological activities. The compounds were tested for their inhibitory effect on the phosphorylating activity of the protein kinase CK2, and their antioxidant activity was also determined in three commonly used assays. The hydrazones were evaluated for their radical scavenging against the DPPH, ABTS and peroxyl radicals. Several compounds have been identified as good antioxidants as well as potent protein kinase CK2 inhibitors. Most hydrazones containing a 4-N(CH₃)₂ residue or perfluorinated phenyl rings showed high activity in the radical-scavenging assays and possess nanomolar IC₅₀ values in the kinase assays.     

Preceramic paper-derived Ti3Al(Si)C2-based composites obtained by spark plasma sintering

The paper describes the structure and properties of preceramic paper-derived Ti₃Al(Si)C₂-based composites fabricated by spark plasma sintering. The effect of sintering temperature and pressure on microstructure and mechanical properties of the composites was studied. The microstructure and phase composition were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. It was found that at 1150 °C the sintering of materials with the MAX-phase content above 84 vol% leads to nearly dense composites. The partial decomposition of the Ti₃Al(Si)C₂ phase becomes stronger with the temperature increase from 1150 to 1350 °C. In this case, composite materials with more than 20 vol% of TiC were obtained. The paper-derived Ti₃Al(Si)C₂-based composites with the flexural strength > 900 MPa and fracture toughness of >5 MPa m^1/2 were sintered at 1150 °C. The high values of flexural strength were attributed to fine microstructure and strengthening effect by secondary TiC and Al₂O₃ phases. The flexural strength and fracture toughness decrease with increase of the sintering temperature that is caused by phase composition and porosity of the composites. The hardness of composites increases from ~9.7 GPa (at 1150 °C) to ~11.2 GPa (at 1350 °C) due to higher content of TiC and Al₂O₃ phases.     

The Current State of Analysis,Synthesis, and Optimal Functioning of Multiproduct Digital Chemical Plants: Analytical Review

Theoretical Foundations of Chemical Engineering - An analytical review of the state of multiproduct chemical plants has been proposed. A comprehensive analysis is made of works of Russian and...     

Diluted chemical bath deposition of CdZnS as prospective buffer layer in CIGS solar cell

In this study, dilute chemical bath deposition technique has been used to deposit CdZnS thin films on soda-lime glass substrates. The structural, morphological, optoelectronic properties of as-grown films have been investigated as a function of different Zn²⁺ precursor concentrations. The X-ray diffractogram of CdS thin-film reveals a peak corresponding to (002) plane with wurtzite structure, and the peak shift has been observed with the increase of the Zn²⁺ concentration upon formation of CdZnS thin film. From morphological studies, it has been revealed that the diluted chemical bath deposition technique provides homogeneous distribution of film on the substrate even at a lower concentration of Zn²⁺. Optical characterization has shown that the transparency of the film is influenced by Zn²⁺ concentration and when the Zn²⁺ concentration is varied from 0 M to 0.0256 M, bandgap values of resulting films range from 2.42 eV to 3.90 eV while. Furthermore, electrical properties have shown that with increasing zinc concentration the resistivity of the film increases. Finally, numerical simulation validates and suggests that CdZnS buffer layer with composition of 0.0032 M Zn²⁺ concentration would be a promising candidate in CIGS solar cell.     

Sleepy keeper style based Low Power VLSI Architecture of a Viterbi Decoder applying for the Wireless LAN Operation sustainability

Analog Integrated Circuits and Signal Processing - Remarkable progress in the field of wireless communication has created a research interest for Viterbi decoder with long duration of battery life,...     

A benzoate coprecipitation route for synthesizing nanocrystalline GDC powder with lowered sintering temperature

Electrolyte powders with low sintering temperature and high-ionic conductivity can considerably facilitate the fabrication and performance of solid oxide fuel cells (SOFCs). Gadolinia-doped ceria (GDC) is a promising electrolyte for developing intermediate- and low-temperature (IT and LT) SOFCs. However, the conventional sintering temperature for GDC is usually above 1200 °C unless additives are used. In this work, a nanocrystalline powder of GDC, (10 mol% Gd dopant, Gd_0.1Ce_0.9O_1.95) with low-sintering temperature has been synthesized using ammonium benzoate as a novel, environmentally friendly and cost-effective precursor/precipitant. The synthesized benzoate powders (termed washed- and non-washed samples) were calcined at a relatively low temperature of 500 °C for 6 h. Physicochemical characteristics were determined using thermal analysis (TG/DTA), Raman spectroscopy, FT-IR, SEM/EDX, XRD, nitrogen absorptiometry, and dilatometry. Dilatometry showed that the newly synthesized GDC samples (washed and non-washed routes) start to shrink at temperatures of 500 and 600 °C (respectively), reaching their maximum sintering rate at 650 and 750 °C. Sintering of pelletized electrolyte substrates at the sintering onset temperature for commercial GDC powder (950 °C) for 6 h, showed densification of washed- and non-washed samples, obtaining 97.48 and 98.43% respectively, relative to theoretical density. The electrochemical impedance spectroscopy (EIS) analysis for the electrolyte pellets sintered at 950 °C showed a total electrical conductivity of 3.83 × 10^?2 and 5.90 × 10^?2 S cm^?1 (under air atmosphere at 750 °C) for washed- and non-washed samples, respectively. This is the first report of a GDC synthesis, where a considerable improvement in sinterability and electrical conductivity of the product GDC is observed at 950 °C without additives addition.     

Structural and Dielectric Properties of (1-x) (Al0.2La0.8TiO3) + (x) (BiZnFeO3) (x = 0.2 − 0.8) nanocomposites

Journal of Inorganic and Organometallic Polymers and Materials - (1-x) (Al0.2La0.8TiO3)?+?(x) (BiZnFeO3) (x?=?0.2–0.8) [ALTBZFO] nanocomposites were synthesized via...